Speed dating scarborough ontario
Sound It's got the best tone, but it's not the loudest (when used for bass). Both the YBA-1 and YSR-1 each have 4 input jacks, so I can jumper the channels and use both the bright and normal volumes to adjust my tone. 1966 early model, cosmetically it's in pretty good shape, the tolex is perfect, the grill has two tiny snags over at one end, but it seems this amp may have fallen face first at some time, when i got it there were only two of the 'chicken head' knobs, and the front panel screw holes were stripped, so you could just pull it off; there's no dents or anything in the faceplate, not even a scratch, internally it's perfectly clean, no dust or gunk anywhere, recently, [October 1998] CAD 0 used, together with a mathing used 4x12 cab, bought at a pawn shop, October 1998 CAD 0 [used], seen at Used Music, Ottawa, November 1998 [US?Better sound as a Fender Bassman; lower powered, would work just fine in a blues or lower volume setting (when used for bass or guitar). ] 0 [used], a 1978 YBA-1 together with a 1977 YT-15, both mint [US?437 volts); this may have gotten higher after 1971, but into the summer of 1971 I'd expect the plate voltages on 6CA7s to be down substantially from the YBA-1A; have the chassis sliding-in ala Fender.Last versions have that easily identified rubber and 'chrome' molding running around each end of the head cabinet; mine is from 1971 and is this last version; 1972 models have no choke; [a 1978 is] black with the black plastic fabric and [has] the baby bumper trim, [it has] two 6CA7 and three 12AX7A tubes in it [and] no fuse holder, just a red reset button I put Mullard EL34s in my YBA-1.] 0 [used], very early model, the serial number is 0278, which places it in 1966, uses 6CA7 tubes as specified in the tube chart, no tube rectifier, and the marshall style phenolic turret board, also, it has the hole in the chassis for the tube rectifier socket, but it is blocked with a circular steel plate, the 5 volt rectifier heater winding at the power tranny is cut about 2 inches out, December 1998 Rating Very good one. I have a 1977 YBA1 with a matching YT-15 cabinet [...]. It's probably not worth a tird as a collector's item but this amp really screams. I rate my YRM-1 second to my YBA-1, because it does not have as much balls.This must have been one of the last real Traynor amps made... Also, my YBA-1 sounds great at all volumes, including low setttings. 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), logo 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), front view, angle 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), front view 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), back view 1966 YBA-1 Bass-Master, chassis 1966 YBA-1 Bass-Master, wiring 1968 YBA-1 Bass-Master (serial number 2xxx), front view, angle 1968 YBA-1 Bass-Master (serial number 2xxx), front view 1968 YBA-1 Bass-Master (serial number 2xxx), logo YBA-1 Bass-Master, catalog page YBA-1 Bass-Master, catalog page YBA-1 Bass-Master, schematic 10/1966 YBA-1 Bass-Master, schematic 6/1971-1974 YBA-1 Bass-Master, schematic 5/1974 - Please note: This schematic has a serious error in it.
i stuck a master volume on the back, jumped the channels, and cranked both channels to 7-8, plugged in my custom shop '61 reissue sg, and it kicks so much ass [through 4x12 25w greenbacks] its indescribable i bought both a 1971 yba-1 and a 1972(? [...] the yba-1a is currently beating the snot out of an old mesa 4x12 with 90 watters in it. this would make sense to me considering how very crushing it is and yet chimey. The only real problem was it seemed to be blowing fuses.
[Oct 2002] US 0 used; one can be bought for under [US] 0 - a total bargain US 0 [used], needed a little work but playable, cheap buy US 9 used, you can get one cheaper CAD 0 [used], good condition, seen at Songbird Music, Ottawa, November 1998 (since January 1999 though, it had changed its condition to 'very good') Rating very good amp My personal opinion is that the YBA-1 is better for guitar, while the YBA-1A is preferable for bass.
My YBA-1A [...] uses 6550s and it's the best rock bass head that I've owned.
typically playing a new gibson les paul "faded" through them. Even after a friend helped me switch the power supply to todays standards and no buzz and shocks occured. I am told it may need some work on the tubes (cost about same as amp itself). 1971 YBA-1A Bass-Master Mark II (top not removable despite later style case), front view, angle 1971 YBA-1A Bass-Master Mark II (top not removable despite later style case), front view 1971 YBA-1A Bass-Master Mark II (top not removable despite later style case), back view YBA-1A Bass-Master Mark II, catalog page YBA-1A Bass-Master Mark II, schematic 1/1969-12/1970 YBA-1A Bass-Master Mark II, schematic 1/1969-12/1970 YBA-1A Bass-Master Mark II, catalog pages, manual, fan conversion, schematic 1/1966, schematic 1/1969-1/1972, schematic 1972-2/1973 YBA-1A Bass-Master Mark II: Looks to be the same as the other one with a choke except it shows 6CA7 as the power tube instead of 7027 (Larry).
(Aaron, Craig, Dan Kukkonen, Dan Lear, Eric Knudsen, Greg, Jay Rogers, John, Jon Aley, Kraig Olmstead, Laws from Lawsstudio Canada, Moon Keith, Tim Baier, viva Analog at bc.ca/~jc, Features volume and tone controls only; it has two inputs, seems to be high and low, no major difference Two 6V6 power tubes This one is a '67 [amp] and is in amazing shape. ) speaker that looks identical to the 15" Jenson in my '64 Fender Vibroverb.
A 1967 YBA-1 is reported to feature a diode rectifier.